“ESP-M2 from esp8285 Serial Wireless WiFi module” has been added to your cart.
View cart
Showing 1–20 of 62 resultsSorted by latest
-
$2.11
Thank you for visiting our product page! We strive to provide you with an effortless shopping experience. Our checkout process is simple and offers various shipping options with tracking. Furthermore, we believe in maximizing the value of your purchase. On this website, you can find detailed instructions on how to use this product and explore…
-
$3.11
- Based on ESP-8266EX
- Supporting the D1 MINI
- The Arduino compatible, using Arduino IDE for programming
- 11 X I/O pins
-
$3.71
Thank you for visiting our product page! We strive to provide you with an effortless shopping experience. Our checkout process is simple and offers various shipping options with tracking. Furthermore, we believe in maximizing the value of your purchase. On this website, you can find detailed instructions on how to use this product and explore…
-
$3.58
- Communication method: Zigbee
- Flash CC2531ZNP-Prod firmware for zigbee2mqtt applications
- Leads out 8 IO connectors
- Debugging interface
- Size: 57x17x7mm/2.24×0.67×0.28inch
-
$3.31
- Chip type: W5500
- Supports both 3.3V & 5V.
- Hardwired TCP/IP Protocols: TCP, UDP, ICMP, IPv4, ARP, IGMP, PPPoE
- 10BaseT/100BaseTX Ethernet PHY embedded
- Supports automatic response (full duplex / half duplex mode)
- Supports 8 independent sockets simultaneously
- Internal 32Kbytes Memory for Tx/Rx Buffers
-
$3.11
- Flash Memory: 8 KB
- SRAM: 512 Bytes
- EEPROM: 512 Bytes
- I/O Pins: 6 general-purpose I/O pins
- Timers: 2 x 8-bit Timer/Counters
- ADC: 10-bit ADC (8 channels)
- PWM: 6 channels (on pins 0, 1, 2, 3, 4, 5)
- Interrupts: External and internal interrupt capabilities
-
$2.11
- On-board 500ma 5V Regulator
- Built-in USB
- 6 I/O Pins
- 8k Flash Memory (about 6k after bootloader)
- I2C and SPI (vis USI)
- PWM on 3 pins (more possible with Software PWM)
- ADC on 4 pins
-
$5.83
Thank you for visiting our product page! We strive to provide you with an effortless shopping experience. Our checkout process is simple and offers various shipping options with tracking. Furthermore, we believe in maximizing the value of your purchase. On this website, you can find detailed instructions on how to use this product and explore…
-
$3.42
- The main board consisting of an ATmega328 with the to 5V.
- The latest version of the LilyPad supports automatic reset for even easier programming.
- The back side of the LilyPad is now completely flat.
- This version of the LilyPad now uses the new ATmega328 at 8MHz.
-
$1.13
- Input voltage range: 4.5V-15V
- Output: 3.3V (note: the 5V pin is connected to the input power supply of the module)
- Interface: TYPE-C
- Size: 30 * 18.5mm
-
$18.78
- Along with the development, the board is equipped with a slice of PIC16F877A chips
- Mixer ZIF40 activity IC convenient takes PIC microcontroller reused
- Pieces of eight LED light-emitting diodes (entertaining diversions experiment)
- Four pieces of Yang digital tube
- Mixer 1 * 4 separate button
- Pieces of 4 * 4 matrix buttons
-
$11.37
- C8051F340 development board,
- component layout compact circuit trace specification,
- onboard two LEDs and two buttons,
- a standard DB9 serial port (female port),
- a miniSD card holder.
-
$1.66
Thank you for visiting our product page! We strive to provide you with an effortless shopping experience. Our checkout process is simple and offers various shipping options with tracking. Furthermore, we believe in maximizing the value of your purchase. On this website, you can find detailed instructions on how to use this product and explore…
-
$4.27
- The V3.0 version began to use a lead-free process
- The pin header is a gold-plated pin header
- Support MicroPython programming
- Support Arduino programming
-
$1.34
- Package Type: LQFP;
- Number of pins: 48;
- Kernel: Cortex-M3;
- Operating frequency: 72MHz;
- Storage resources: 64K Byte Flash, 20KByte SRAM;
-
$9.17 – $19.83
- STM32F407VET6 chip main parameters
- The Kernel: 32-bit RISC architecture (M4;
- The Features: Single-cycle DSP instructions
- Operating frequency: 168 MHZ
- 210 DMIPS / 1025 DMIPS/MHZ
- Operating voltage: 1.8 to 3.6 V
-
$20.77
- STM32 microcontroller with LQFP64 package
- Two types of extension resources
- On-board ST-LINK/V2-1 debugger/programmer with SWD connector
- Flexible board power supply
- Three LEDs
-
$4.81
- Processor : ATmega328P-AU
- Operating voltage :5V Recommended VIN input voltage :6V to 15V
- Digital IO Pins:22 (6 of which are used as PWM output)
- Analog input pin:8 (A0~A7)
- IO pin DC current:40mA
-
$4.47
- Type: Voltage Regulator
- Condition: New
- Application: Computer
- Supply Voltage: 3.3v-5v
- Model Number: ATmega32U4 5V 16MHz Module
-
$2.18
- Using ATMEGA328P-AU microcontroller.
- Working voltage: 5V
- Input voltage (limited): 6-20V
- Input voltage (recommended): 7-12V
- I/O pin DC current: 40mA
- Processor: ATmega328
